Hi Chaps Just joined as I'm facing an issue with my mondeo after a remap. It's a 2018 Mondeo ST line edition with the 180ps Duratorq engine and quickshift box. Its a stage 1 map carried out by a local reputable guy, he's mobile and does it on the driveway. The car has only gained an extra 20bhp b This happened with my 2008 Kuga 2.0 tdci 140. Came on with no loss of power and it drove fine. It took 2 visits to the dealer to find out it was a faulty DPF sensor. Buy Ford Mondeo Particulate Filters and get the best deals at the lowest prices on eBay! FORD MONDEO MK4 2.0 TDCi DPF DIESEL PARTICULATE FILTER 6G91-5H250-HA 2007 Faulty DPF pressure sensor. 4. Open or shorted wiring in the DPF pressure sensor circuit. 5. DPF regeneration has not been completed. 6. Overuse of fuel system additives. Ash accumulation is a side effect of DPF filtration and completed regeneration cycles. Ash accumulates near the rear of DPF filtration element.
1288 posts · Joined 2005. #1 · Dec 21, 2023. I have recently built and installed Damian's Canbus box into my mk5 2.0. All works great, however it shows DPF regeneration cycles - and it seems i am regenerating every 50 miles or so. the Soot load climbs quite quickly but never hits 100% - after a regen it drops to about 30% again and the time
Re: 2011 Mondeo - constant DPF regeneration, cannot reset DPF_SOOT_LD Post by darekM » Fri Dec 14, 2018 9:36 pm I've left the car at offical Ford dealer/service yesterday.
Wondering if anyone can help with a idling issue I've been having with my 2006 Ford Focus 1.6 TDCI. The other day, on a 25 mile journey, I had to pull up at a set of traffic lights. When I did the car started idling erratically between 500 - 1500 rpm, as I pulled away from the traffic lights I noticed the car jerking and/or hesitating slightly.
Cause of DPF blockage and regeneration failure and what you need to do to fix it. Diagnostic brand, Autologic has shared a ‘technical top tip’ for technicians dealing failed DPF regeneration on Ford’s 1.6, 2.0 and 2.2 Duratorq TDCi engines. Possible fault codes likely to show include P244C, exhaust temperature too low for particulate
Hi ive got a 59 plate 2 litre tdci mondeo, earlier it did a regen when i pulled onto my drive so i left it for about 10 mins to finish and then switched the car off like normal, later on i went out again and drove no more than another 10 miles and when i pulled back onto my drive it did the same
2.0 TDI Failing The Regenerate The DPF. DPF light came on last week; took it for a run on Saturday to clear it. It failed to clear and the 'glow plug' light has started to flash; then the 'emissions' light illuminated. Other symptoms the cruise control has deactivated (I suspect this is normal and due to the engine faults), and the car is
ford mondeo DPF CleaningIncreased Flow Rate From132 - m3/h to 386 - m3/h The DPF Centre is part of Quantum Tuning Ltd the largest vehicle remapping company. My faithful 2010 Mondeo 2.0 duratorq estate, DW10C, has started throwing P0130 & P0135 errors, which would suggest that the heated oxygen sensor - variously known as H02S11 sensor, HEGO (heated exhaust gas oxygen) or Lambda probe - is failing. It won't now perform DPF regens. The part in question is the 5-wire sensor 9F472.
Ford Model: Focus 1.6 TDCi Ghia & 2.0 Ecoblue estate. Ford Year: 2019. UK/Ireland Location: Other/NonUK. Posted February 10, 2015. I don't think the law has changed but MOT regs were tightened up early last year, yes I have had my DPF removed, and no I don't regret it one bit. Quote.
Hi All, New joiner and know zero about cars and engines so please go easy on me. I purchased an 2008 S-MAX 2.0 TDCI (Automatic Diesel) 3 months ago. I only ever do short journeys and very rarely go on the motorway. Last week my engine Amber light came on, the car runs as normal (not in limp mode)
